Don’t let Windows errors hold you back.
If you see an error code on your computer for the best Cisco troubleshooting teams, check out these repair ideas. Cisco Discovery Protocol (CDP)Show version.Ring.Build a route.Telnet.View interface control codes and interface status.Cisco shutdown command.Display the IP route.
Routing is the process of establishing a route between two or more routers. Here is a list of 10 basic CCNA routing troubleshooting commands with examples to help you troubleshoot a network configured using a DF protocol such as RIP or eigrp OSPF.
What are Cisco CLI commands?
The Cisco IOS Command Line Tool (CLI) is the primary user interface of choice for configuring, monitoring, and maintaining Cisco devices. This user interface allows you to directly and easily execute Cisco IOS commands, whether you are using a hub console, terminal, or remote device access methods.
Follow the image provided in the entire command I want to share with you for troubleshooting a Cisco network and that network needs to be configured using OSPF.
- Show user interface
- Show IP Interface
- Show Logs
- View IP Logs
- Show current configuration
- Show IP Route
- Show IP Log Database.
Which command is used to display routing troubleshooting information?
Use the show ip Direction command to get detailed information about the routes configured on the hub. Please note that the modem can only forward packets to my networks specified in its route.
Of the top 10 CCNA routing troubleshooting commands, the ping command is the most commonly used. The ping packet is ready for Internet Groper. He workt on the new OSI network layer and uses the ICMP protocol. First of all, it is a command that should be used when troubleshooting network problems. You can check if two devices are connected or not with ping command like
for PC 1 and PC 2 are associated with a router with IP addresses 10.0.0.2 and 10.0.0.2. To test the connection, run command # 1 ping 10.0.0.2 from the PC. If you have received a TTL, it means that the connection has been established.
Show User Interface
This command allows you to find out the current popularity of the interface, which (port) determines whether a port is enabled or disabled, which IP address is assigned to it, its data transfer mode, etc.
Show IP Interface
This command allows you to find out the current state of the interface (port), which consists of an address and a broadcast IP address, and even reports whether a slot is active or inactive.
The effect of traceroute follows on the end-to-end path that a container takes through the network. This allows users to keep track of the exact selection of data sent over the network.
For example, you really want to follow a route between a powered on PC and PC 4, which in addition to 22.214.171.124 is assigned an IP address of 10.0.0.2. So the start command is on PC 1: Traceroute 126.96.36.199, and then the route that can reach the destination can be shown.
Show Protocol PNG
This log really only shows the current state of the connection to the router and its IP address. This command is useful when families just want to check the IP addresses of all interfaces found on the router.
Show IP Protocol
This command helps you determine what protocol can be configured on your router.
Telnet is any protocol that allows you to communicate with remote computers (called hosts) outside of the TCP / IP network (for example, your current Internet). Telnet command actually allows you to access the router and configure the following items remotely.
Use the telnet Host IP Address command frequently to connect to the router’s Internet support
For example, you want to use Router 4 to connect remotely from Router 1. So I run the command
Show Current Configuration
This can be considered a basic routing troubleshooting command. It shows all the configuration you have done on the switch. It will show you all the commands you have executed through the router, including the specific hostname, address, IP clock rate, and route.
Byeset IP Route
How do you troubleshoot a Cisco switch?
Define the problem.Find devices that are having problems.Check VLAN configuration.Check the configuration of the trunk lines.Check the configuration of the access ports.Solve customer problems.
This routing command allows one person to view all routes that can reach all destinations.
Show The IP Of The Standard Protocol As A Database.
This is the last command in the list of top 10 CCNA routing troubleshooting commands. Review the IP schema database that works with EIGRP and OSPF. It shows selected networks in different areas. Friends,
Again, this is a list of 10 basic CCNA routing troubleshooting commands with one script. I hope you find this article helpful and helpful in troubleshooting any Cisco network.
Video Tutorial Of The Ten Most Important CCNA Commands For Troubleshooting Routing Commands
What are the basic troubleshooting commands?
You will be able to run standard network troubleshooting commands like arp, ping, ping6, traceroute, traceroute6, NSlookup and AvgRTT from the admin console. You can use these Internet tools to view the system’s network path to an identified server.
Topp Cisco Felsökningskommandon
Principales Comandos De Resolución De Problemas De Cisco
Najważniejsze Polecenia Cisco Dotyczące Rozwiązywania Problemów
Die Wichtigsten Cisco-Befehle Zur Fehlerbehebung
Top Cisco-opdrachten Voor Probleemoplossing
I Migliori Comandi Per La Risoluzione Dei Problemi Di Cisco
Лучшие команды Cisco для устранения неполадок
주요 Cisco 문제 해결 명령
Principais Comandos De Solução De Problemas Da Cisco
Principales Commandes De Dépannage De Cisco